 |
FAQ's Freestyler |
|
- What are the minimum bay requirements for the FreeStyler?
- Does the FreeStyler operate on hydraulics or electric?
- Do I need to have doors on my bay?
- Do I need to have a heated bay? Floor heat?
- What is the warranty on the FreeStyler?
- Does Belanger provide construction drawings and installation schematics?
- Why should I use a spot free rinse?
- What utility services does the FreeStyler require?
- How many packages can be programmed?
- What do you mean toggle between primary and secondary menus?
- Does the FreeStyler page out errors, malfunctions and faults?
- Is the FreeStyler reclaim ready?
- What type of detergent is recommended?
- What customer appealing upgrades like tri-foam, lighting packages, and rust inhibitors can be added to the FreeStyler?
- How many wax / drying agents can I apply?
- Does the wheel cleaning system apply chemical?
- How does the wheel cleaning system locate the wheels?
- Is a floor treadle required?
- Are there guide rails on the floor?
- Can the FreeStyler wash dually pick ups?
- Can the FreeStyler wash Hummers?
- What navigational signage is standard?
- Is an operator interface required in a non p.o.s. application?
- Where is the "home" position?
- What are the wash times? How many cars an hour can the FreeStyler process?
- What would be a typical installation time?
- Can I order the machine with cloth material?
- Do we use pneumatic tires to drive the carriage?
- How do we keep the top wheel out of pick up beds?
- Does the FreeStyler weep or "blow-down" to prevent freeze ups?
- Does the FreeStyler have an on-board dryer option? When will an on board dry be available?
- When will the optional white carriage powder coating be available?
- Does the FreeStyler have remote diagonstics? Can I control the operation of the machine and/or retrieve performance data via the internet?
- What are the color choices for the carriage?
- What are the color choices for the Neo-Tex foam?
- Can the FreeStyler be a drive-in/back out?
- Does your machine offer a water saving module? What average volume of water is used on each wash?
- Does your machine measure or adjust to move closer to vehicles to provide a better cleaning job?
- Can your machine wash more than 2 sides of a vehicle at one time and what is the average wash time of your machine?
- Will the FreeStyler support an off board 7 panel service confirmation electronic sign (illuminates applicable service during application)?
- What are the colors of the lights used on the electronic on-board navigational sign?
- When ordering an under vehicle manifold with a FreeStyler, can I use the entrance photo eye to activate the under vehicle wash or do I need an additional photo eye?
- Are there distributors available in every province of Canada and have they completed factory training on service and install?
Minimum bay requirements will be dependent on types of vehicles you would like to wash. The minimum requirements are outlined in the Bay Requirements Document
Electric motor controls with fluid arm controls.
Yes, if your climate falls below 32º F.
Yes, if your climate falls below 32º F.
13 months from ship date.
Yes, we provide standard AutoCad prints for site and construction preparation. Belanger also provides an installation manual that contains all the necessary information.
The effective use of spot-free water will allow the entire vehicle surface including all glass, chrome, and painted areas to dry virtually streak and spot-free. The additional investment creates an additional revenue generating menu item.
What utility services does the FreeStyler require? Electric and water; a phone line is required if the pager module is ordered. Natural gas is required if heat is required for the bay.
A total of 8 packages; this will include 2 banks of 4 packages each.
You can switch the E410 between two banks of pre-programmed packages, containing 4 packages each, to increase the operator’s flexibility in meeting the cleaning requirements of his local market.
Yes, if the pager module is purchased. The Page Module system feature is great for operators that do most of their work remotely. This feature can be programmed with two phone numbers to automatically call if the system detects a fault. You simply program the numbers you wish the modem to call, the call order of the numbers, and the maximum number of pages to be sent. The modem will then automatically page each programmed telephone number and identify the fault code for the machine.
It will require the purchase of an optional reclaim adapter kit.
High quality detergent with good lubricity properties is recommended.
The FreeStyler has many appealing options that will enhance the customer’s wash experience and improve the wash performance including:
• Tri-Color Foam – Triple Foam Pods
• Undercarriage/Rust Inhibitor vehicle wash
• Tire and rocker panel cleaner – Wheel Stinger®
• 2 additional onboard chemical applicators to be used at your discretion.
1. Drying Agent
2. Clear Coat
3. Triple Foam Wax
*All three are optional upgrade selections
Yes, through the use of a CTA-style applicator at vehicle entry.
The front tires are identified by the treadle location, the rear tire is determined by the E410 program during your package set-up.
Yes
At this time the only guide rails are those integrated into the treadle.
Yes, with the purchase of the dual wheel adapter for the treadle.
Yes, the FreeStyler can wash H2 and H3 Hummer models. The H1 is too wide.
Machine mounted directional sign-mounted on the underside of the overhead carriage and consist of bright LED navigation instructions.
No
At the exit end of the rails.
Two minutes and up, depending on the package selection.
Similar to a Vector or less.
No
No, the exit end idler wheels are connected via common shaft, drive motor and floating gearbox which drive the carriage forward and backward.
The carriage has a sonar mounted on the entrance side that detects the rear of the cab resulting in the top wheel being retracted at the precise location.
No. The wash bay temperature must be maintained above freezing at all times.
No, we are not sure when it will be available.
It is currently available with a four week manufacturing lead time.
Available soon on installations that include the E410 operator interface.
Currently available you may choose the color of the oval branding panel on the front of the carriage and the accent striping colors. You may choose from Red, Blue or Black for the branding panel and red/blue, blue/red and black/blue for the stripes.
We will update the color choices as additional options become available.
Solid Red
Solid Blue
Solid Black
Red with Blue Accent Red
with Black Accent
Blue with Red Accent
Blue with Black Accent
Black with Red Accent
Black with Blue Accent
We will update the color choices as additional options become available.
Yes, it is still in development.
Yes, the E410 operator interface offers infinite, owner-level, programming flexibility to better manage all aspects of system operation. The FreeStyler fresh water requirement is a mere 20 g.p.m. and is at full capacity only when the wash wheels are spinning. The E410 programming determines actual water consumption by wash cycle speed, i.e., the faster the travel speed, the less water will be consumed.
Advanced configuration features permit additional opportunities for maximum efficiencies. Water and/or chemical applications can be delayed by programming “from start” and “from end” values into the E410, minimizing water and chemical waste.
Additionally the FreeStyler is fully compatible with reclamation systems that have the potential to lower fresh water consumption by 80%.
No, the FreeStyler is treadle activated system. The treadle is a simple, rugged component that is used to position the car and activate the FreeStyler once the car is in position. The activation treadle features independent forward and rear sensing that ensures correct tire position. The Dual stage back-to-back wash arm cylinders with air-over-oil controls then deliver precise wheel pressure, regardless of the vehicle’s contour, for a superior wash result each and every time.
Yes, the FreeStyler is a 5-arm system that quickly and effectively washes two-four sides of a vehicle a once; depending on the wash pass. With the capability to wash 20-30 cars an hour (based on vehicle size and wash package) the FreeStyler’s 5-arm design means faster washes, happier customers, and more profits.
Yes, the Freestyler will support any devise that is a purely resistive load (light bulbs). The lights can be ran parallel with the function that is on. The combined load should not exceed 3amps. In the event that it does exceed 3 amps it may be put on to its own output and linked to the original. The entire control system may not exceed 20amps. The best answer to your question is most of the time, but not always. Also sign quality should be good enough not to cause nuisance GFCI faults. Please call if specific info needed.
The colors used for the lights are:
• Enter Arrow - Green
• Back Up - Amber
• Stop - Red
The photo eyes at the entrance can be programmed with the E410 to activate one or more functions.
completed factory training on service and install?
Yes, Belanger has an extensive worldwide distributor network with a broad Canadian presence. From our world class distributor network made up of the most experienced and knowledgeable car wash specialists in the business, to our customer-committed Technical Support Service & After Market Support Team, Belanger, Inc. is your complete business partner.